Homemade Wooden Yo-Yo
First a flat face is turned on a piece of hardwood, then a 5mm hole is drilled through and it is finished off by screwing a short M6 bolt through that hole, from the other side. Turning one half of the Yo-Yo to shape. Feb 08, · The Wooden Yoyo is an early-game yoyo, and generally the first available to the player. It is the weakest of all yoyos. It remains deployed for about four seconds before returning automatically to the player. It has a spin duration of 4 seconds, and can reach up to 9 tiles. Its best modifier is Godly or Demonic. Both modifiers increase the average damage output by the same amount. 1 Crafting 1.
So I figured ou t recently that nobody had posted any hpw your own yo yo from scratch. All there is on yo yo's is ti to change cheap plastic ones into yo as cheap plastic ones that sleep. So I decided to make my own and here it is! Hope this helps you guys out! You need to attatch the how to open the otterbox for iphone 4 to the drill how to do the knife game and just cut two circles out of the wood like in the picture.
The wood will probably burn because of the hardness but thats no maks just go slow. Here you are going to need to smooth out the circles using woodd file or sand paper or something. This is also where you choose which side is going to be facing in where the string is and which out. I picked the side with the prettier grain to be the outside. Now on the inside you need to round the edges off at more of an angle to that the string has kind of a rail to be fed into the center if it gets off balanced.
Make sure there are no rough edges or splinter that could catch the string. On previous models i have sprayed the yo yo with laquer to give a slicker, smoother surface for the string to rub against and it makes it shiney. But I like the natural wood feel.
This is a really easy step and it involves putting the bolt throught the washer and one circle. Put the washer on the outside part and then put the bearing or spacer in on the bolt on the inside. Really easy the pictures say all. Hoow the last part. You must put the other circle on now. Aa make sure that the side you chose to be the inside is on the inside.
Then put the washer around the little remaining bolt and screw on the nut. Do not make the nut and bolt too tight or else makd spacer or bearing will dig into the wood and pinch the string.
And now you are done. Go out and yo yo it up yo!!! As you use it it will self ballance itself so you don't have to worry about ballance which is a plus. And as I said before it will only sleep for about 5 seconds before it spins out unless you have a bearing or a really slick spacer.
Introduction: Homemade Wooden Yo-Yo. Now you need to attatch the string to the spacer or bearing. Not mak difficult. Participated in the Woodworking Challenge View Contest. Did you make this project? Share it with us! I Made It! Aquaponics for Everyone! Garlic Gardening by DanPro in Gardening. Backyard Arsenal 5 years ago on Introduction. Reply Upvote.
Make a Wooden Yo-Yo
Item: Qty. Description #/2" - 5/8" (mm) thick hardwood, ie. maple or walnut: you can also use plywood which will be stronger; you only need enough to make two yo-yo discs which are about 2 1/2" (63mm) in diameter.
To begin I drilled a 5mm hole in the centre of two blanks, which I will be used to turn the body of the Yo-Yo, the heavier the wood the better!
The holes are to accept an 6mm screw chuck. First a flat face is turned on a piece of hardwood, then a 5mm hole is drilled through and it is finished off by screwing a short M6 bolt through that hole, from the other side.
Turning one half of the Yo-Yo to shape. The Yo-Yo can be of any cylindrical shape you like, in fact, hollowing out the centre slightly should increase the performance of the Yo-Yo by concentrating the mass on the outer edge.
Measuring the diameter of the turning. When watching a video by Frank Howarth , he suggested weighing the two halves of the Yo-Yo to ensure they are fairly similar, in order to achieve a balanced Yo-Yo which runs smoother. Nevertheless I was easily able to re-mount the heavier one to the lathe and give is a really quick sand to remove that tiny amount.
In all honesty this step is not all that necessary, if the diameter of the two halves is the same that should be close enough! However, in this instance I decided if the project was worth doing, it was worth doing right! Following turning the next stage is to make an axle.
Commonly wood is used, but as I had some spare 6mm steel shaft in the workshop which I thought might work well instead. What ever material you do decide to use I would suggest a diameter of between 6 and 8mm. Note:If you go larger you might need to re-drill the holes for the axle to fit. Here I am using playing cards as a guage. The axle can simply be sanded a little at a time until the ideal distance is achieved. I suggest starting out with 10 and then decide if you need to go any further.
Once a few coats of finishing oil or your preferable finish has been applied the string can be attached. If the string is tied tightly the Yo-Yo should easily bounce up and down for you.
I attached the string by tying a small knot in the end of it, then by untwisting the very bottom of the string I was able to slide the string over the axle. This is the most common way in which Yo-Yo strings are attached. Finally the two halves can be attached together. If you have a really tight fit you might be able to simply push them together, if this is not the case, like with mine, a single drop of CA glue in the holes should hold it adequately. This leaves the ability to pull the Yo-Yo apart if needed.
<- What does the human diaphragm look like - How to connect dlna devices->