Chainmaille Bracelet Step 1: Materials & Tools. You'll need a pair of needle nosed pliers and a pair of bent nosed pliers (or just two pair Step 2: Working With Jump Rings. Jump rings are basically a circle of metal that has a slit in it, so it's not really a Step 3: The Basic Chain. We'll. Mar 02, · Subscribe to the Rio Grande Channel: waltergretzky.com how to make a chain mail bracelet from silver and copper jump rings in this Beads Baubles and.
To create this article, 18 people, some anonymous, worked to edit and improve it over time. This article has been viewed 56, times. Learn more For the beginner chain mail enthusiast, this is an ideal project for producing an elegant bracelet. The project level is easy and it uses the most basic pattern, European 4 in 1. After making your first chain mail bracelet, you'll gain the confidence to make more advanced chain mail objects.
Gow and Warnings. Things You'll Chainmzil. Related Articles. Gather your supplies. These are listed in the "Things You'll Need" section below. You can make the entire bracelet with a single color ring, or use two colors.
In this article, the center color is red and the edge color is blue. Open a ring in your center color. To open a ring, grasp each end with pliers and twist them in opposite directions, as shown in the image.
Put four edge color rings on the open ring. Then close the open ring by twisting the ends back together. This unit is called a chainlet. Make sure that the ends close together tightly. There shouldn't be a gap, and the ends shouldn't overlap. Lay the chainlet on a flat surface as shown.
The center ring should go behind the top two rings and in front of the bottom two rings. You may need to flip the corner rings over to get this arrangement right, but it's very important that they are arranged this way.
Make another chainlet and lay it out in the same way, directly below the first one. Loop the center ring behind the bottom two rings of the top chainlet. Loop that same ring over the top two rings of the lower chainlet. Don't let the rings from the previous step fall off. This step is tricky!
Make more chainlets. Then attach them together until you have a long enough bracelet to fit your wrist. Try hunting around in craft stores near your house. Depending on what color you want, you could even check braclet local hardware store.
Yes No. Not Helpful 0 Helpful 0. Include braceler email address to get a message when this question is answered. By using this service, some information may be shared with YouTube. Keep trying! If you mess how to update micromax canvas 2 a110 to kitkat the first time, it can be hard to try again.
The good news is that the more you practice, the better you get! Helpful 4 Not Helpful 0. Helpful 3 Not Helpful 1. Submit a Tip All tip submissions are carefully reviewed before being published. Related wikiHows How to. How to.
Co-authors: chainmakl Updated: November 5, Thanks to all authors for creating a page that has been read 56, times. Also, the advice to lay them on a flat surface was one I hadn't thought of duh! More reader stories Hide reader stories. Did this article help you? Cookies beacelet wikiHow better.
Introduction: Chainmaille Bracelet
Feb 01, · Recommended jewelry pliers for making chainmail: waltergretzky.com rings to get started: waltergretzky.com this video, I go over a pattern. Dec 16, · A specially made 15 minute video explaining everything you ever wanted to know about byzantine and how to make it. filmed in HD with macro cameras and presen.
This instructable will make a chainmaille bracelet, both a simplified form and a more complicated one. We'll start with the tools necessary and the basics of working with jump rings, then get into the pattern.
If you're already familiar with working with jump rings, head over to step 3 to start the chain. Apologies if the orange background is too bright, but it helped to show the details of the rings. Whatever surface you work on, it's helpful to be different than the material you are working with, and to have edges, so nothing rolls away.
Tools: You'll need a pair of needle nosed pliers and a pair of bent nosed pliers or just two pair of needle nosed. If you're going to be working with jump rings a lot, you could use one pair of needle nosed and a jump ring tool, but I often find myself grabbing the bent nosed even when using the tool.
The ring tool goes over your thumb or whatever finger works best for you and provides leverage for opening and closing. It has different slots for different gauges thicknesses of rings. Essentially, you use it just like pictured, only with your thumb in there. Materials: Jump rings! There are lots of instructions around the internet on how to make your own, but I got a set of different colored and different sized ones from Amazon.
For the pattern in this instructable, you'll need A small rings, B rings just big enough to fit completely around the small rings, and C rings slightly bigger than that. I used different colors for ease of seeing the process. Jump rings are basically a circle of metal that has a slit in it, so it's not really a solid circle. To OPEN a ring: Twist like ripping a paper, but gently , don't pull like unplugging an extension cord.
When twisting, you can apply a little pressure to increase or decrease the size of the circle. This is handy if you make your own rings and there's too much of a gap, or if you buy them and they have too much overlap. If you've never worked with jump rings before, practice on all your sizes without doing any weaving, just to get the hang of it. Most metal rings are pretty forgiving, but I have broken rings being too enthusiastic. It is also helpful at this point if you close up all the A rings.
You'll mostly be just sliding them onto other open rings, so it's easier to make sure they're all neat and closed now. Bonus: most jewelry has jump rings involved, so if you ever have an earring come apart or a necklace chain break, now you have some basic skills to attempt to fix it.
We'll start with a simple 2x2 chain. Start with one C ring. Open it, slide on four A rings, and close it again. Add a second C ring, through all four A rings, but not through the first C ring. Your third C ring will go through two of the A rings, and add two more. A fourth C goes exactly through the same As as the third. Continue on, two Cs through two previous As and adding two new As. See the pictures to get an image of this. Continue until the bracelet is long enough.
You'll want enough room so it doesn't cut off circulation, but not so much it will fall off. Really, this will depend on the preferences of the intended wearer.
Now it's time for the B rings. This part is a little bit fiddly, but be patient and you'll get the hang of it. Open the first B ring. Again, the pictures will help. As you go, it may be helpful to drape the bracelet between two fingers to hold it in place. Again, this is a little tricky, but keep going and don't give up! You could end here, by adding a simple lobster clasp to one end and ONE A to the end the clasp will attach to the single ring.
First, make a second helm's weave chain the same length as the first. Then, use As to connect the two chains together at the Cs. In the pictures, I switched to thicker rings in different colors, but you can achieve the same thing with two As, and I'll refer to them as the connecting As. Now that you've practiced the helm's weave with the two chains, and have connected them, it's time for an even trickier and fiddlier helm's weave.
Using Bs remember, this is the ring that fits completed around but not too loosely the connecting As , go between a pair of Cs, around the connecting As, between the other Cs, and close. As you go, you'll notice the bracelet is becoming less and less flexible. The Bs stabilize the chainmaille.
This might mean you end up wanting it longer or shorter. To finish, you can either add a lobster claw, or other type of claps. The picture has a three-ringed clasp that I bought at a craft store. Now that you know some chainmaille basics, you can make earrings or other things. Pictured is a set of somewhat matching earrings that I made.
First, I laid out the jumps rings needed, then connected them up. Be careful with earrings, though, because chainmaille can get a bit heavy, and if your ears aren't used to it, you don't want to overdo it. Introduction: Chainmaille Bracelet. By lastchancetuesday Follow. More by the author:. Participated in the Jewelry Contest View Contest. Did you make this project? Share it with us! I Made It! Cardboard Horn Amplifier.
Kid Name Circle Board by julien.
<- How can i stop cats from pooping in my garden - What are the best gold stocks to buy->